[elektro] OT: Canon I320 hiba

[Bali Zoltan]

Ezt a printer service tool-t a sm is irja.
A neten meg mindeféle progit le lehet hozzá
tölteni csak az originalt nem.  Nincs meg valakinek
a Canoné ?

Köszi

Üdv.  Zoli




----- Original Message ----- 
From: "Pipi" <lista at puzsar.hu>
To: <elektro at tesla.hu>
Sent: Wednesday, August 26, 2009 5:04 PM
Subject: Re: [elektro] OT: Canon I320 hiba


> Bali Zoltan írta:
>> Sziasztok !
>>
>> A fenti nyomtató  elvileg ezt villogja:
>> "Waste ink full or platen waste ink full error"
>> A fejet sem hozza a csere pozicióba.
>>
>> Mit lehet ezzel kezdeni ? Lehet valamit takaritani ?
>> A manual azt mondja "Replace the printer as it has failed".
>> Még nem szedtem szét.
>>
>> Köszi
> hali!
> nem a printert kell replacelni, hanem a benne lévő tinta gyűjtő filcet (aztán lehet hogy bírja még, félig sincs)
> ellenőrizni kell ha nem akarsz tintafoltot az asztalodon, utána szervízprogival le kell törölni a hibaüzit
> ennyi infóm van még, nem próbáltam...,
> valamelyik canonnál ez a gombot nyomkodom dolog az első konnektorból kihúzásig(áramszünetig) működött,
>  utána újra kellett jáccani, de valamelyik progival helyre lehetett hozni
>
>  Re: Canon i350 waste tank full by PrintX (7/29/04 3:48 PM) reply + / -
> Try this it is generally for the i320 i255 but it should do the trick.
>
> i320 waste ink counter reset.
> 1. Turn off the printer.
> 2. Press and hold the POWER button, turn on the printer.
> 3. The indicator should be green.
> 3. Press and release the RESUME button , the indicator should be orange.
> 4. Press and release the RESUME button again, the indicator should be green.
> 5. Release both buttons.
> 6.Connect the printer to PC.
> 7.Open General Tool software,choose ˇ°USB PORTˇ±.
> 8.Choose ˇ°SET DESTINATION 1 ˇ±,OK!
>
> You can download the software at: http://www.it0577.com/yezmao/i320.exe
>
>  --------------------------------
>  here are the steps to make it a permanent reset. please follow these instructions carefully as you might end up doing the wrong 
> thing and end up not resetting your printer.
>
> Using the I320 Service Tool
> 1. setup your pc and install windows 98/98SE/ME. this is required to ensure that the i320 service tool will run.
> 2. after installation (which includes all drivers), install the appropriate printer driver for the printer. you can download it 
> from canon's driver download site.
> 3. run the i320 service tool and follow the steps below.
>
> EEPROM reset / Destination setting
> 4. install the print head, and while holding down the POWER button, plug in the AC cable (the green lamp lights up.)
> 5. while still holding down the POWER button, press the RESUME button twice and release the POWER button to enter the Service Mode 
> (each press of the RESUME button changes the LED color: the LED
> lights in orange the first time, and in green at the second time.)
> 6. connect the printer to the computer, select "USB PORT" using the i320 service tool.
> 7. Destination setting
> -other than Japan: select "1" in "SET DESTINATION"
> -Japan: select "2" in "SET DESTINATION"
> EEPROM reset
> EEPROM is reset at the same time when the destination is set.
>
> you can download the i320 Service Tool from this address:
> http://www.it0577.com/yezmao/i320.exe
>
> note: the "I/F dll can not be loaded" error means that you were running the i320 service tool without the printer's drivers 
> installed on your computer. make sure that you have installed the printer
> driver first before attempting to reset the printer.
>
>
>
>
>
>
> -- 
> Pipi
> http://www.puzsar.hu
>
> -----------------------------------------
>          elektro[-flame|-etc]